CLASSIC CHARGE CONTROLLER - Features and Programming
Features, Programming & Bugs
Frequently Asked Questions
- CLASSIC - 3-Stage Charging Explained
- CLASSIC - ALARM - Classic is RESTING and alarming "GROUND FAULT"
- CLASSIC - ALARM - My Classic(tm) is alarming "ARC FAULT", how can I fix this?
- CLASSIC - ALARM - OCP Explained
- CLASSIC - AUX1 GENERATOR - Using AUX-1 to start a Generator
- CLASSIC - AUX2 Clipper Mode Volt & Width explained
- CLASSIC - AUX2 Logic Input Explained
- CLASSIC - AUX2-AUX1 NITE LIGHT ADJUST
- CLASSIC - BREAKERS - Circuit Breaker Wiring Diagram
- CLASSIC - BUG LIST as of FW2096
- CLASSIC - DIVERSION - WASTE_NOT_HIGH EXPLAINED
- CLASSIC - DIVERSION using WASTE_NOT_HIGH
- CLASSIC - Dual CLocks & Timekeeping Explained
- CLASSIC - ENDAMPS - How do I figure what ENDAMPS should be?
- CLASSIC - ENDAMPS - Setup for more than one Classic
- CLASSIC - ENDAMPS - Why is ENDAMPS not triggering at my ENDAMPS setting?
- CLASSIC - F-ME - How do I test FOLLOW-ME?
- CLASSIC - F-ME - How to setup Classics in true MASTER/SLAVE Mode
- CLASSIC - F-ME - Why are my Classics not sharing the work when networked with Follow-Me?
- CLASSIC - FIRMWARE - How to tell if my Classic Firmware is matched to the MNGP?
- CLASSIC - HARDWARE Factory Restore AKA JP1-BOOT
- CLASSIC - HOW DO I CLEAR THE LOGS IN MY CLASSIC?
- CLASSIC - How do I use the RFR - Reason For Resting code ?
- CLASSIC - How to use LOGIC LOW Aux-2
- CLASSIC - HYDRO MODE - What is Twiddle-Dither ?
- CLASSIC - HYPERVOC - PV IN rises up to over voltage by itself
- CLASSIC - LED - The flashing BLUE LED, what it means...
- CLASSIC - LITHIUM - How do I set the Classic to charge Lithium batteries (archived)?
- CLASSIC - LITHIUM Quick Start (archived)
- CLASSIC - LITHIUM Quick Start Simplified
- CLASSIC - MODBUS - How do I get to the MODBUS Editor?
- CLASSIC - NIFE - Using the Classic to Charge NiFe Battery
- CLASSIC - PV IN - IN breaker is OFF or It is night, Classic show voltage on the input?
- CLASSIC - PV IN - Zero volts on Display for IN VOLTAGE
- CLASSIC - RESET - How do I invoke the setup Wizard and Factory Settings Restore?
- CLASSIC - SERIAL MODBUS ADDRESSING
- CLASSIC - SOC% is not displaying on the MNGP
- CLASSIC - SOC: Force WBjr to read 100% SOC
- CLASSIC - Testing AUX2 and WhizbangJr tips
- CLASSIC - WBJR - How do I limit Battery Current based on the Whizbang jr. ?
- CLASSIC - WBJR - Installed a WBjr and my SOC% just keeps going down.
- CLASSIC - What is the MNGP and what are the rubber keys used for ?
- CLASSIC - WHAT IS VMM and HOW DO I DO IT ?
- CLASSIC - Why did my Classic KWh Production RESET during the day...
- CLASSIC - WHY MY CLASSIC DOES NOT SEND DATA TO MYMIDNITE
- MNGP HAS FACTORY RESET COMMAND
- SPEECH - How do I setup and use the Voice feature?
- What is the SERIAL data rate of the Classic RS232 MODBUS?
- WHIZBANG JR - Technical Information
- WHIZBANG JR - Technical Information 2
- WIND MODE - Classic Wind Curve Programming
- WIND MODE - Dual Classics Wind Curve Programming
- WIND MODE - How do I use a Classic on DIY Wind Install ?